ugh think im confused...again

j2508 · 10-23-2009, 08:34 PM

i am actually not sure what my ribcage measurement is..thought it was 26 by adding 13 and 13, but my BWD is 13 .that is what I heard my PS say. said it was 13 on both sides.

if id go with a high profile i would need to go pretty large wouldn't i to make sure i didnt have a gap?

like 500 ish for hps and 425+ for mod plus?

i was looking at this chart

http://www.justbreastimplants.com/im...t_profiles.htm

stolz · 10-23-2009, 08:49 PM

all my info is in my stats

I got Allergan Inspira silicon textured rounds that were 13cm in width and had a projection of 5.3cm.
My PS doesnt like to go much over the BWD, so these were spot on, and right now i am LOVING my boobs at 8 days old

Dare · 10-23-2009, 08:56 PM

Your BWD measurement is more important than your ribcage measurement IMO. You can properly measure your ribcage by putting a measuring tape right under your breasts, holding it firmly all the way around your torso there, but not tight.

If you have 13cm BWD, then yes..HP's would likely need to be around 500-600cc's. If you don't want that much volume/projection, then go down in profile to a mod+ or mod. If your ribcage truly is 26", then 500+ cc's would look fairly busty on you. I have a ribcage of 27.5", and a "before" BWD of 12.9cm's. HTH

10-23-2009, 08:34 PM	#1
j2508 love my new boobs Join Date: May 2009 Location: Peoria, Illinois Posts: 132 Thanks: 46 Thanked 23 Times in 20 Posts	ugh think im confused...again i am actually not sure what my ribcage measurement is..thought it was 26 by adding 13 and 13, but my BWD is 13 .that is what I heard my PS say. said it was 13 on both sides. if id go with a high profile i would need to go pretty large wouldn't i to make sure i didnt have a gap? like 500 ish for hps and 425+ for mod plus? i was looking at this chart http://www.justbreastimplants.com/im...t_profiles.htm

10-23-2009, 08:49 PM	#2
stolz Thinking thinking.... Join Date: Sep 2009 Location: Mid North Coast, NSW Australia Posts: 329 Thanks: 58 Thanked 81 Times in 79 Posts	all my info is in my stats I got Allergan Inspira silicon textured rounds that were 13cm in width and had a projection of 5.3cm. My PS doesnt like to go much over the BWD, so these were spot on, and right now i am LOVING my boobs at 8 days old __________________ 5'7" 136lbs/62kgs Pre breast augmentation - hollow 32D/10D (C cup of tissue) Post breast augmentation -32F at 3 months post op 450cc HP unders both sides Ribcage 30" BWD 13cm breast augmentation date - 16th October 09 ~I DO NOT ACCEPT FR'S IF YOU JUST SEND ONE THRU WITHOUT A COMMENT ON MY PAGE OR ARE NOT AN ACTIVE REGULAR POSTER =)~

10-23-2009, 08:56 PM	#3
Dare Comfort & Joy Join Date: May 2007 Posts: 1,881 Thanks: 512 Thanked 1,125 Times in 806 Posts	Your BWD measurement is more important than your ribcage measurement IMO. You can properly measure your ribcage by putting a measuring tape right under your breasts, holding it firmly all the way around your torso there, but not tight. If you have 13cm BWD, then yes..HP's would likely need to be around 500-600cc's. If you don't want that much volume/projection, then go down in profile to a mod+ or mod. If your ribcage truly is 26", then 500+ cc's would look fairly busty on you. I have a ribcage of 27.5", and a "before" BWD of 12.9cm's. HTH __________________ Friend Requests gladly accepted ONLY from members that have picture albums of themselves, and are "elite" active posters.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Confused on size and asymmetry	lisa789	CC Amount / Size	7	09-13-2009 01:52 PM
So confused	SDBABY	Breast Lifts	18	07-29-2009 09:20 PM
Confused about my final bra size...	metalrox	CC Amount / Size	9	06-20-2009 02:38 AM
Just got back from consultation.... confused!	KatieTrina	General Breast Augmentation Discussion	12	02-05-2007 07:50 PM
Confused about implants being filled to???	Pattibee	CC Amount / Size	9	02-05-2007 04:19 PM